8700k overclock guide This is a topic that many people are looking for. passionistsisters.org is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, passionistsisters.org would like to introduce to you ASUS MAXIMUS X HERO – Overclocking Test and Guide 8700K (en). Following along are instructions in the video below:
“And welcome to a new video in the last video. The z370 battle of the the cheap. We did a comparison of the cheapest z370 motherboards and the question is it even necessary to invest like double or triple. The amount of money into a high end overclocking or gaming motherboard in the z370 battle of the cheap i found out that the asrock.
Z370. Pro 4 can clock up to 4200mhz on the memory and also 50ghz to 51ghz on the 8700k was not really an issue so today. We will take the results from this z370 battle of the cheap and compare those results with the asus maximus. 10 hero just by looking at it you can already see that this is a motherboard out of the higher price category.
So you can straight. See the io shield to the cover here that s looking quite nice. It s still plastic. But it looks good.
There s also a lot of rgb stuff going on on the motherboard. Which looks quite nice if you set it to the correct color. And also you have those brushed aluminum look heat sinks everywhere like the heatsink from the m2. Ssd in the middle and i think it gives it a very high quality look also the pcb looks very nice personally one of the most important features for me is the vrm and the vrm on this board is really solid.
It s an 8 phase. Vrm and compared to the cheaper boards in the z370 battle of the cheap those ports usually have like 4 phase. Vrm designs and they don t always use power stages like an fully integrated power stage. They sometimes use like high side and low side mosfets split up into two packages and quite cheap components cheap inductors.
So that s probably the biggest difference from this board to the cheapest boards and also obviously the bios one feature. I really like about those boards is this small installation frame is for the cpu you can basically clip in your cpu from the back. And then install your cpu using this installation frame. And well you might laugh about it.
But really it also happens to me once in a while that if you want to mount your cpu you just accidentally drop it into the socket you bend some pins. It s not the end of the world if you bend some pins you can always bend them back if they re not breaking. But yeah using this installation well usually your cpu doesn t drop into the socket and it s very safe to install the cpu this way. So let s go over to the result data of this test.
The first test. We have is the dram testing. So you can see the table comparing to the four cheapest motherboard and you can see the asus maximus. X hero did the whole test successfully so even up to.
4200 mhz with 2x8gb was not an. Problem. Unfortunately i didn t have. 4166 memory sticks.
Available. Because asus is advertising. This as memory speed that should work on the board..
But i don t really have doubts that it s working because all of this was working quite nicely. If you experience any kind of memory issues with the board. There is in the dram timing control there s an option. It s called maximus tweak.
And there is mode 1 and mode. 2. And sometimes it helps to just set this to mode. 2.
To allow your memory speed to run higher. So let s go over to the maximum power draw in this chart you can see that the cheaper boards. They could run from 115 to 131 watts under load more load would cost vrm to throttle. So this was the maximum power.
I could pull from the cheapest boards and the asus maximus x. Hero was able to draw 210 watts. Which is quite a lot more it s almost double the power consumption. So that shows how much stronger the vrm on this board is compared to cheaper boards.
So let s translate the power draw into real word. Data so you can see the cheaper boards could. Run. Like.
50ghz and the msi. Z370 a pro could even. Run 51ghz. And this is on an open test bench.
Without any airflow. So that s like the worst case scenario running prime95. Obviously. If you re running this into a case that s very well ventilated you can even hit higher numbers here you can see that the asus.
Maximus x hero was able to. Run even 53ghz at 1424v and that s actually more than enough keep in mind that the cpu. I was using is extremely binned cpu so this is far. Above average usually you will be able to run 50ghz to 52ghz on your cpu depending on how good your sample is obviously you have to delid your cpu to hit those numbers like.
51. 52. You have to delid your chip to hit those numbers stable. For.
Prime95 running 53ghz and 144v it would eventually throttle down. To 50ghz but well. 53 at 142v is still quite a lot and should be fine for 99 of the daily overclocks talking about overclocking..
Let s go over to 5ghz overclocking tutorial. You can use this as a baseline. If you want to overclock with the maximus x hero. So let s start with the overclocking nthis guide will work for the i7 8700k and also for the i5 8600k.
There is no difference between those cpus when it comes to the overclock. So if you just received your mainboard you should first check for newer. Bios versions on the asus website and update your bios first after doing that we go back to the bios and we set the ai overclock tuner to xmp and select no. Here you can see that i m using an xmp profile of 3600.
And i m using 4 memory sticks with 8gb each and you can see on the right side currently the memory is running only 2133mhz so we have to configure the memory first and that s also what i recommend so first apply this and then we will go back to the bios now you can see on the right side that the memory is running at. 3600mhz which is the correct clock and the voltage is also correct at 135v. Next thing. We do is disable the asus multi core enhancement and set the avx instruction core ratio negative offset to 3 this way the cpu will clock down by a ratio of 3.
Under avx load avx is an instruction of your cpu. And it basically puts a much higher workload on your cpu resulting in a higher power consumption. And it s also much more stressing for the cpu. So using an negative offset of 3 means that your cpu will clock down by 300mhz under load.
So cpu core ratio you set to sync all cores and set this one to 50 this means that we will overclock the cpu to 50ghz obviously you can always clock higher afterwards. But you should start with the stable base disable cpu. Svid. Support.
Then go to external digi. Power control and set cpu load line calibration to level 6. This way the voltage will stay stable under load. And it will stay at around the same level.
If you use level 7. You will have quite a big overshoot nover. The idle voltage. That s not what we want so i would recommend using level 5 or level.
6. In internal cpu power management. You set the long duration power limit and short duration power limit to the maximum go back out. And go to the cpu core cache.
Current limit. Max also set this one to the maximum basically. We ll disabling. All the power limits.
So. The cpu will always stay stable at the highest clock and it will not throttle down minimum and maximum cache. We should start at 42 you can always increase it afterwards once you are done with a whole overclocking thing you can adjust the cpu cache to a higher level in certain applications..
When they re really memory heavy it can help you by increasing the cache clock bclk aware adaptive voltage is a feature that can basically increase your cpu voltage. While you are also increasing the bclk. But i personally would never use this feature. I would always set both manually so cpu core cache.
Voltage we set it to manual and set it to 135v which should be a. Safe base you can use up to. 140 142. That should be no problem especially when your cpu is delided.
I don t think there s an issue using such voltages because i i ve seen several cpus that have this level like 135. In stock voltage. Already so shouldn t be an issue you see that cpu vccio and cpu system agent voltage they are already affected by the xmp usually they are much lower. Like 11v roughly maybe even lower you can see it s.
123. 128. On auto now. Which is still fine you can use up to like one point.
Three five volt without any issues. But probably it doesn t help too much if you increase it that high so that s it already for 50ghz. We go to asus overclocking profile and just save our settings typing anything here save it to profile 1. Then we will apply this setting and go to windows.
So we are back in windows 10. So what we have to do now is obviously test the cpu for stability. So you have to check everything. In cpu z.
First you can see that my cpu is clocking down in idle. Which is absolutely fine. There is no effect on stability. If you don t want that you go to your power.
Saving options and you set well it s a german os. But you set your power saving plan to high. Performance and then you can see the cpu is clocking up to 50ghz and it will stay always at 50ghz on the mainboard you can see that i m running the bios version 0505. Which was the most recent version available at this point on memory you can see i m running the 32gb.
Gskill trident. Z rgb memory with a cache of. 4200mhz and here you can see. The memory speed is correctly applied with 1800mhz.
Aka. 3600mhz. Because it s ddr4 double data rate can also see it here in spd..
What kinds of modules. I m using so after applying settings like this it s very helpful to just do a cinebench run because this way you can check if there is a quick issue in temperatures you can see i m hitting like 70 degrees celsius. Which is absolutely fine. Because obviously my cpu is delided you can also see the cpus staying stable here.
You can always right click into the cpu z to see the core clock of all cores you can also see the cpu voltage under load is 136v. Which is due to the load line calibration so that s also correct now we can see the performance was 1654 points which is absolutely where we where we should be at at 5ghz well 2030 points depending. Where your cache. Frequency is at and also what kind of memory modules and memory.
Speed. You re using for the real stability. Testing we will use prime95 in the version 266. Which is without avx and the load of this is roughly the same as running cinebench r15.
So it s a very good. And also real world performance testing and stability testing. So set minimum fft and maximum fft to 1344 check run ffts in place. And just simply hit.
Okay. Now you should leave this running for around one hour keep checking the temperature in core temp. You can see i m now hitting like 75 degrees celsius. Which is still absolutely fine you can go up to like 95 degrees celsius.
But i noticed on those cpus that the higher you go in temperature it definitely affects stability of your cpu. So if you have a better water cooling loop. And you hit like maybe only 50 degrees celsius under load. You might be able to clock higher than me here.
If you have stability issues at this point. You still have headroom in. The voltage so you can go up to like. 141v 142v and check if this helps you also still keep in mind.
That you have to stay away from like higher than 95 degrees celsius. So always keep the temperature in mind. If this is running stable you can also go back to the bios and increase the cpu multiplier to like 51. Or 52.
Which equals 51ghz or 52ghz and simply test how high you can push your cpu. I hope the small tutorial helped you if you have any kind of questions problems with the tutorial just simply put it in the comments. ” ..
Thank you for watching all the articles on the topic ASUS MAXIMUS X HERO – Overclocking Test and Guide 8700K (en). All shares of passionistsisters.org are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.