how to install chamberlain 1/2 hp chain drive garage door opener This is a topic that many people are looking for. passionistsisters.org is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, passionistsisters.org would like to introduce to you How to Assemble and Install a Chamberlain Chain Drive Garage Door Opener. Following along are instructions in the video below:
Thank you for choosing chamberlain today were going to show you how to assemble assemble and install a chamberlain garage door opener in a garage with a sectional door a finished ceiling. The model. Well be installing is a chain drive garage door opener your product and installation may vary products that feature unattended control of the door such as timer to close or myq.
Functionality should only be installed in garages with sectional doors and cannot be used on swing out or one piece doors this video is intended for demonstration purposes. Only please consult the manual for complete instructions and safety information youll begin by assembling your garage door opener. And then youll install it you should plan to set aside a couple of hours.
But you may need more time before beginning check the balance of the door to make sure it moves freely and does not drift an unbalanced door may prevent your garage door opener from functioning properly for more information about checking the balance of your garage door watch this video. Your garage door should also have horizontal and vertical reinforcements already installed these provide support and help prevent damage to the door. Before you assemble your garage door opener.
Its a good idea to lay out the parts. They include the motor unit. The rail and trolley assembly with chain.
The header and door mounting brackets and the other parts including hardware refer to your manual for a list of tools and additional items you may need the support bracket for mounting. The motor unit to the ceiling is not provided youll also need to supply light bulbs begin by placing your garage door opener on protective cardboard and setting it on the floor. About 10 feet away from the garage door to assemble the rail.
Carefully remove the door arm and hanging bracket parts lay out the rail sections on the floor. With the tapered ends pointing toward the garage door. The front rail section with the window goes on the door end of the rail.
Make sure. The cutout rail tab is on top slide. The tapered ends of the rails into the larger ends.
Placing the rail on top of packing material. And the motor unit will help with assembly insert a screwdriver into the hole in the second rail section from the motor unit at the motor unit end of the rail slide. The trolley assembly toward the screwdriver making sure the release lever points toward the motor unit.
Insert the u bracket with the flat side down push firmly until it reaches the stops use a mallet to assist. If needed install the cover protection bolt. Making sure not to over tighten remove the bolts from the top of the motor unit and use them to attach the u bracket to the motor unit when mounting the u.
Bracket. Hand tighten the bolts do not use power tools attach the chain spreader to the motor unit with two screws feed. The cable through the window on the front rail before inserting.
The idler pulley secure the idler pulley in place. With the provided hardware use a flathead screwdriver to lift the cutout rail tab to a 90 degree angle. Connect the cable to the trolley using the master link pull the other end of the chain.
Until the trolley rests against the screwdriver extend the chain and wrap it around the sprocket on the motor unit make sure the sprocket teeth engage the chain. And it is not twisted make sure the cable is around the cable pulley connect the chain to the threaded shaft. Using the master link hardware thread the inner nut and lock washer onto the threaded shaft insert the threaded shaft through the hole in the trolley loosely thread the outer nut onto the threaded shaft.
Leaving a little slack. Now that the chain is installed remove the screwdriver from the rail. The chain needs to be tightened.
So that the bottom of the chain rests about one quarter inch above the base of the rail tighten the outer nut until the chain is at the proper height. When the chain has been properly tightened secure the inner nut your garage door opener is ready to install do not proceed with installation until you have thoroughly read all of the instructions and safety information. In your instruction manual.
This demonstration. Only provides an overview of an installation in a garage with a sectional door and finished ceiling your product and installation may vary. The header bracket will be centered over the garage door and fastened to a structural support do not attach the header bracket over drywall.
If there is a header bracket already properly installed use it if possible raise the garage door to the highest point of travel and make a mark two inches above this using level is helpful with the door closed place the bottom of the header bracket on your mark and make marks for pilot holes be sure to refer to the instruction manual for the correct drill bit size install the header bracket using the provided hardware. Its time to place. The assembled garage door opener into position.
You may find it easier to have a helper use a ladder to support. The motor unit and a second ladder or step stool to reach the header bracket connect the rail to the header bracket using the clevis pin and secure in place with the ring.
Open the garage door and place a two by four under the rail. This will put the motor unit at the proper height for connecting to the support bracket. If a properly installed support bracket is not already in place.
You must supply one along with the hardware for fastening. It to the structural supports in the ceiling. Weve already drilled pilot holes into the structural.
Supports and now were attaching the support bracket in a place that will be centered over the garage door opener measure the distance from the support bracket to the garage door opener measure and cut the hanging bracket connect the hanging bracket to the garage door opener. And the support bracket remove the two by four and lower the garage door install the light bulbs thread the emergency release rope through the handle and tie it off then install the emergency release rope to the trolley making sure the handle is within reach. But at least six feet above the floor being sure to avoid contact with vehicles.
This is to prevent accidental release. If your garage door is made of lightweight material. Such as fiberglass aluminum or light steel make sure both horizontal and vertical reinforcements are installed before attaching the door bracket.
The door bracket will be centered under the header bracket attach it to the vertical reinforcement on the top panel position. The top edge of the door bracket. Two to four inches below.
The top edge of the door or directly below any structural support across the top of the door it attaches to the vertical reinforcement on the top panel using the provided hardware. If there is a door bracket already properly installed. Its easier to use that the outer trolley needs to be close to the garage door.
So you can install the door arm. If you need to move it disconnect the trolley by pulling down on the emergency. Release.
Handle and slide the trolley over to the door. The door arm. Consists of a curved section and a straight section use the provided clevis pins to connect the straight door arm to the trolley and the curved door arm to the door bracket align the curved and straight arms so they appear to be positioned between one and two oclock use the provided hardware to connect the two parts.
Your installation is not complete. Until. The protector system has been installed the protector system consists of safety.
Reversing sensors. Which are mounted on each side of the garage door at floor level safety. Reversing sensors are to be installed no more than six inches from the floor snap.
The sensor bracket onto the door track then mount the safety. Reversing sensor using the provided wing nut and bolt. If your garage is not pre wired for safety.
Reversing sensors. Follow the instructions for routing. The wires.
That are attached to the sensors since this garage already has wiring in place. Well follow the directions for connecting the safety. Reversing sensors to the existing wiring.
Now follow the directions for wiring. The safety. Reversing sensors to the motor unit insert the white wire in the white connector and the black wire in the gray connector next install the door control your product may come with one of these three styles single button multifunction or lcd follow the directions in your instruction manual for connecting the wires and mounting the door control.
It must be mounted within sight of the door at a minium height of five feet above floors landings steps or any other adjacent walking surface so small children are not able to reach it and away form all moving parts of the garage door wire the door control to the motor unit by inserting the white wire in the white connector and the red wire in the red connector. Its time to plug in your garage. Door opener complete your installation by aligning.
The safety. Reversing sensors youll also need to program. The travel limits test the protector system and perform the safety reversing test click any of the links to watch a video if you have a wi fi garage door opener or are using a myq enabled garage door opener with a chamberlain internet gateway click on one of these links to complete your installation congratulations on installing your chamberlain garage door opener.
Thank you for choosing chamberlain be sure to check out our other products. And accessories when you visit us on the web at wwwchamberlaincom. .
Thank you for watching all the articles on the topic How to Assemble and Install a Chamberlain Chain Drive Garage Door Opener. All shares of passionistsisters.org are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.